MIMA MQK30M-ZSM540 or ZSM650: Which lift height fits?
Model comparison for operational planning
If you choose an electric MIMA MQK30M for high shelves or multi-level storage areas, you should not just look at the maximum lifting height.The MQK30M-ZSM540 and the MQK30M-ZSM650 have many basic data in common, but differ significantly in terms of lifting height and overall height.This comparison classifies the published vehicle data and shows which information should be checked before making a specific selection.
At the time of publication, the MIMA MQK30M-ZSM540 five electric vehicles.For the MIMA MQK30M-ZSM650 Four electric vehicles are shown.The number is a snapshot and not a promise of future availability.
The published data at a glance
- 3.000 kg: Rated capacity for both versions
- 5.400 or 6.500 mm: published lifting heights
- Triplex: Mast information in both model lists
- 48V/600Ah: Lithium-ion battery according to vehicle data
| feature | MQK30M-ZSM540 | MQK30M-ZSM650 |
|---|---|---|
| Number of vehicles shown | 5 at the time of publication | 4 at the time of publication |
| Drive type | Electrical | Electrical |
| Rated load capacity | 3.000 kg | 3.000 kg |
| Lifting height | 5.400 mm / 5,4 m | 6.500 mm / 6,5 m |
| Height | 2.535 mm / 2,535 m | 2.902 mm / 2,902 m |
| mast | Triplex | Triplex |
| Battery specification | 48V/600Ah lithium-ion | 48V/600Ah lithium-ion |
| annual field | 2026 | 2026 |
| Operating hours field | 1 | 1 |
These figures show a clear technical difference: the ZSM650 provides 1.100 mm more lift height than the ZSM540. At the same time, its published overall height of 2.902 mm is 367 mm greater than that of the ZSM540. A higher lift height therefore comes with a greater overall height. Which version may be considered for a specific operation can only be assessed after comparing the building, travel routes, racking and load data.
When is the lifting height the decisive factor?
The required lifting height should be derived from the actual bearing geometry.It's not just the height of the top shelf that matters.The position of the fork, the height of the pallet or load carrier, necessary safety distances and the operational storage height must also be taken into account.
At 5.400 mm or 5,4 m, the MQK30M-ZSM540 offers a lower published lift height.The MQK30M-ZSM650 reaches 6.500 mm or 6,5 m. The higher variant can be relevant if shelf levels are planned accordingly.However, this does not mean that there is a general suitability: the mast, load, attachment and operating conditions must be considered together.
These values should be present before selection
- Height of the top shelf level actually used
- Dimensions of pallet, load carrier and load
- required clearance during storage and retrieval
- Clear heights of gates, passages and crossings
- Ceiling height as well as possible cables, gates or other obstacles
- Load capacity requirement at the intended working height
Why height is just as important
The height influences whether a vehicle can reach the intended areas.The MQK30M-ZSM540 is specified in the published data as 2.535 mm height.For the MQK30M-ZSM650 it is 2.902 mm.Even a single lower passage can limit the usable route.
Therefore, not only hall gates should be measured before making a decision.Fire protection gates, connecting corridors, transitions between parts of buildings, loading zones and areas under technical installations are also relevant.In addition, it should be clarified to which operating status a specified height dimension refers and which other vehicle dimensions are relevant for the route.
3.000 kg are a nominal load capacity, not a universal residual load capacity
Both model lists mention a load capacity of 3.000 kg or 3 tons.This value should not be understood as a promise that any load at any height can be accommodated with any equipment.This is the published nominal load capacity.
The actual usable residual load capacity depends, among other things, on the load center, the load dimensions, the lifting height and a possible attachment.A long, high or unevenly distributed load may present different requirements than a standard compact pallet.Attachments can also change the weight and load center.The associated load capacity diagram is therefore decisive for the specific configuration.
At least are required for the load capacity test
- maximum load weight
- Load center distance
- Length, width and height of the load
- Designated maximum lifting height
- Type and weight of an attachment
- operational load and load carrier
Correctly classify common features
Both model lists mention electric drive, triplex mast and an 48V/600Ah lithium-ion battery.These matches make direct comparison easier, but do not replace a complete operational check.Information such as shift duration, charging windows, driving distances, inclines, ground conditions or energy requirements are not included in the data used here and should therefore not be derived from the battery information.
The year field 2026 and the operating hours field 1 are initially just that: published data fields.They alone are not sufficient to conclusively determine the condition, usage history or classification as new or unused.Such an interpretation is deliberately not made in this comparison.
Practical Decision Matrix
| Test Question | Why it is important | Comparison |
|---|---|---|
| Is 5.400 mm enough for the highest planned shelf position? | Prevents selecting unnecessary or insufficient lift height | Compare ZSM540 and ZSM650 based on the real storage height |
| Are all passages higher than the relevant vehicle height? | The route can be limited by the lowest point | Compare 2.535 and 2.902 mm with the measured heights |
| What load must be moved at the maximum height? | Nominal load capacity does not automatically correspond to the remaining load capacity | Check load center, load dimension, lifting height and attachment |
| Is an attachment intended? | Weight and stem dimensions can influence the load capacity | Evaluate configuration and load capacity diagram together |
| How are loading and deployment windows organized? | The battery information alone does not describe the energy requirement | Enter the deployment profile and loading planning separately |
This allows the selection to be prepared in a structured manner
A reliable comparison begins with measured values from the company.First, lifting and clearance heights should be documented.This is followed by the load weight, load center and load dimensions.Only then can it be assessed which of the published versions is technically closer to the requirements.
The MIMA Forklift truck configurator can be used to put together the requirements in a structured manner.For a specific request, the measured heights, load data, planned work processes and required attachments should be specified as completely as possible.
Compare MQK30M versions based on your data
Check the two model lists at the time of publication or submit the specific application data for further coordination.A binding selection should only be made after checking the complete vehicle and load data.
Frequently asked questions about the MQK30M-ZSM540 and MQK30M-ZSM650
What is the most important difference between ZSM540 and ZSM650?
The most noticeable difference in the published data is the lift height: 5.400 mm for the ZSM540 and 6.500 mm for the ZSM650.At the same time, the heights differ with 2.535 and 2.902 mm.
How many vehicles are shown in the model lists?
At the time of publication, the MQK30M-ZSM540 list shows five vehicles and the MQK30M-ZSM650 list shows four vehicles.These numbers are a snapshot and not a promise of future availability.
Does 3.000 kg mean that any load up to 3 tons can be lifted to 6,5 m?
No.The 3.000 kg are a rated load capacity.The usable residual load capacity must be checked based on the specific vehicle data, taking into account the load center, load dimensions, attachment and lifting height.
What height are the two versions?
2.535 mm is specified for the MQK30M-ZSM540 and 2.902 mm for the MQK30M-ZSM650.For operational planning, these values must be compared with all gates, passages and height restrictions.
Do both models have a triplex mast?
Yes, a triplex mast is mentioned in both current model lists.Further mast and vehicle-specific information should be checked separately for the selected vehicle.
Which battery is indicated in the model lists?
An 48V/600Ah lithium-ion battery is specified for both versions.However, no binding statements can be made from this alone regarding running time, charging requirements or suitability for a specific shift model.
Does the year field 2026 and one hour of operation mean that the vehicles are new?
No.These two fields alone are not enough to conclusively classify the condition or usage history as new or unused.The complete details of the specific vehicle are decisive for this.
What information should a specific request contain?
Maximum lifting height, lowest clearance, load weight, load center of gravity, load dimensions, planned attachments as well as information on travel routes and operational sequence are helpful.